Solar-Powered Pedestrian Sign
Introduction to the Solar-Powered Pedestrian Sign:
The Solar-Powered Pedestrian Sign is a type of traffic sign commonly used at crosswalks and other pedestrian-only areas to remind pedestrians not to
cross the street indiscriminately and to use designated crosswalks, thereby reducing traffic accidents. It features ultra-bright wide-angle LEDs developed in-house by Weimei, paired with optical lenses, and utilizes imported 3M high-intensity reflective film
to provide excellent visibility even at night.
Share This Products :
Solar-Powered Pedestrian Sign Features:
1. Combines active and passive lighting; features proprietary ultra-bright wide-angle LEDs paired with optical lenses and imported 3M high-intensity reflective film, with a service life exceeding 7 years
2. Wide viewing angle and visibility up to 1,000 meters, allowing drivers to see the sign in advance and prepare accordingly, significantly reducing traffic accidents
3. Ultra-slim design for easy installation; withstands wind speeds up to Beaufort Scale 8
4. Long service life; resistant to UV aging, waterproof, wear-resistant, and corrosion-resistant
600×600mm Solar Pedestrian Crossing Sign
The 600 × 600 mm solar-powered pedestrian sign is installed at pedestrian crossing intersections to alert motor vehicle drivers that a pedestrian crossing is ahead and to encourage them to slow down and yield to pedestrians. By integrating solar power generation, energy storage, active LED illumination, and high-strength reflective film technology, 600×600mm Solar Pedestrian Crossing Sign addresses the poor visibility of traditional reflective signs in low-light conditions at night, during rainy or overcast weather, in tunnels, and at dusk, thereby enhancing traffic safety at pedestrian crossings. (See the figure below.)
Product Features of the 600×600 mm Solar-Powered Pedestrian Sign
Warning and notification function: proactively reminds drivers that a pedestrian crossing is ahead; they are advised to pay attention to pedestrians crossing the road and to slow down in advance to yield.
Self-sufficient solar power supply: Solar panels capture light energy, convert 600×600mm Solar Pedestrian Crossing Sign into electrical energy, and store 600×600mm Solar Pedestrian Crossing Sign in an integrated lithium battery, eliminating the need for an external mains power connection.
Battery energy storage: Supports continuous operation during prolonged cloudy or rainy weather, ensuring that the indicator remains illuminated normally during such periods.
All-weather outdoor protection: IP65 waterproof and dustproof, capable of withstanding heavy rain, direct sunlight, and wind-blown sand; the aluminum panels and frame are resistant to deformation, rust, and UV-induced aging, making them suitable for outdoor environments with extreme temperatures and minimizing fading or deformation during long-term outdoor use.
Visualized long-range detection feature: LED beads are evenly arranged along the contours of the marking pattern, providing long-range illumination and visibility; in low-visibility conditions such as nighttime or during rain or fog, this enables early warning and reduces the risk of pedestrian–vehicle collisions at crosswalks.
Installation features: The clamp-based installation structure requires no excavation or cable routing and is simple to install, enabling rapid deployment at locations without mains power, such as school entrances, rural roads, and campus access points.
The core pain points that 600×600 mm solar-powered pedestrian signage can address for customers
Conventional reflective road signs are difficult to see at night or in foggy conditions, leading to a high incidence of accidents at crosswalks.
This product utilizes LED active lighting; its triangular outline, pedestrian, and crosswalk patterns incorporate built-in lighting, providing long-distance warnings to drivers to encourage them to slow down in advance, thereby effectively reducing the risk of collisions between pedestrians and vehicles at crosswalks.
In the field, there is no utility power supply; consequently, cabling installation incurs high costs, requires a long construction period, and involves cumbersome road-work approvals.
A standalone solar power supply system requires no external power cables and eliminates the need for road excavation; 600×600mm Solar Pedestrian Crossing Sign can be installed directly using pole clamps, significantly reducing civil engineering and utility installation costs and shortening project timelines. It is ideal for locations without grid electricity access, such as rural roads, suburban highways, school entrances, and industrial park intersections.
Conventional markings provide weak warning effects, causing drivers' attention to be diverted and making 600×600mm Solar Pedestrian Crossing Sign difficult for them to notice crosswalks.
Supports both steady-on and flashing dual modes; the flashing mode provides a stronger visual impact, making600×600mm Solar Pedestrian Crossing Sign easier to capture the driver’s attention and enhance warning effectiveness on road sections such as intersections, curves, and areas where trees obstruct the line of sight.
The project budget is limited, and ongoing electricity costs will continue to accrue in the later stages.
Solar energy harvesting requires a one-time investment and incurs no electricity costs during operation; over the long term, 600×600mm Solar Pedestrian Crossing Sign is more economical than using mains electricity for illuminated signage.
Switch Instructions for the 600×600 mm Solar-Powered Pedestrian Sign
Black switch:
light-operated switch
Red switch:
main switch
600×600mm Solar Pedestrian Crossing Sign Installation Instructions
Solar panel installation:
1First, use screws to secure the first bracket and the solar panel from both sides; then use two screws to fasten the second bracket to the already assembled first bracket;
2. Connect the solar power waterproof connector to the luminaire connector, and tighten the waterproof nut in the cable;
3. Next, align the holes in the solar panel and the luminaire, insert the screw and washer, and tighten them;
Band installation:
1.Pass the screw through the aluminum slot on the back of the product; then insert the holes at both ends of the clamp into the screws at those respective ends; screw on the nuts; and secure the clamp to the center of the aluminum slot;
2. Insert the pole between the two clamps and secure 600×600mm Solar Pedestrian Crossing Sign with nuts and washers.
600×600mm Solar Pedestrian Crossing Sign
600×600mm Solar Pedestrian Crossing Sign
600×600mm Solar Pedestrian Crossing Sign
This product features an aluminum casing; heavy pressure should be strictly avoided to prevent damage to the casing. The device must be powered on only under the supervision of a qualified professional; do not disassemble or assemble the luminaire without authorization.
600×600mm Solar Pedestrian Crossing Sign
• Warranty Period: 3 years; the warranty covers only the main unit of the lighting fixture; accessories are not covered; custom-made products are excluded.
• Return Method: Customer returns
• Scope of Exclusion: Malfunctions resulting from human-induced damage or natural disasters are not covered under the warranty.
• Logistics Note: The shipping cost for returned items shall be borne solely by the shipper.
| Product Name | Solar-Powered Pedestrian Sign |
|---|---|
| Product Model | WDM-BZ-RX-70X70CM |
| Product Dimensions | 70 x 70 cm / 60 x 60 cm / Customizable |
| Light Color | Yellow + White |
| Housing Material | Aluminum |
| Operating Mode | Flashing |
| Number of LEDs | 21 white, 46 yellow |
| Solar Panel | 15W/6V |
| Lithium Battery | 16AH/3.7V |
| Operating Voltage | 3.7 volts |
| Protection Rating | IP66 |
| Visibility Distance | 1–1,000 meters |
| Installation Method | Clamp-on |
| Hook Diameter | 76 mm |
| fittings of a machine | quantity | Notes |
| Sign | 1 unit | Warning requirements |
| solar panel | 1 set | Self-contained energy storage via solar panels |
| Solar panel mounting bracket | 1 set | Fixed solar panels |
| Clamp + screw rod + nut | 2 sets | Fixed sign |
| certificate | 1 copy | As a certificate of material release upon qualification |
| product specification | 1 copy | Includes product technical specifications, illustrated installation steps, and a safety and maintenance guide. |
