Model 600 Double-Sided Through-Hole Canopy Light
Introduction to the Model 600 Double-Sided Through-Hole Canopy Light:
The Lane Indicator Series is a line of signal lights designed to meet the needs of highway tunnels and high-grade road tunnels. The double-sided through-hole canopy light is a common type of traffic signal. It displays a red cross and a green arrow on the same screen, using these symbols to indicate traffic conditions for vehicles and pedestrians. This product is primarily used at highway toll plazas and tunnel entrances, with one set of canopy lights typically installed above each lane. It has two display states: a red cross and a green arrow. It operates in only these two modes: the red cross indicates “No Entry,” while a green arrow indicates that passage is permitted. The red cross and green arrow lights emit a high-intensity beam, allowing drivers to see them from a distance so they can slow down in advance, guiding them to pass through the toll station correctly, safely, and smoothly.
Lane indicators are installed above the centerline of traffic lanes inside tunnels. With dual-sided displays, they guide vehicles to travel in the designated direction within the tunnel, enabling effective control of traffic conditions and ensuring the implementation of the tunnel traffic guidance plan. Lane indicators use ultra-high-brightness LED lights arranged in combinations to form single or multiple graphics, including symbols such as a cross, downward arrow, left arrow, and right arrow. They feature high luminous intensity, excellent visibility, clear signaling, and strong moisture- and water-resistant properties.
Share This Products :
600 Double Sided In Line Canopy Traffic Light
The Type 600 dual-sided plug-in red cross and green arrow canopy light, also known as a lane control sign or canopy signal light, is a core electromechanical traffic equipment for highways and tunnels, designed to display lane access permissions in real time: Red cross = the lane is closed – no entry permitted; Green downward arrow = the lane is open – entry is allowed. This model features dual-sided illumination, allowing the signal to be clearly observed in both forward and reverse directions; 600 Double Sided In Line Canopy Traffic Light is suitable for installation at toll stations and tunnel portal frames. (As shown in the figure below)
product function
Red cross indicator illuminated：
The lane is closed; vehicles are prohibited from entering. This message is commonly used for lane maintenance, accident management, closing toll plaza lanes, or implementing tunnel closure measures, and serves to remind drivers to change lanes in advance.
The green downward straight arrow is lit up：
The lane is open, allowing vehicles to proceed normally; this indicates that 600 Double Sided In Line Canopy Traffic Light is safe to enter the lane.
(Two signal patterns alternate; only one pattern is illuminated at any given time to prevent drivers from misjudging the situation.)
Dual-sided synchronized lighting visual function：
The product features a dual-sided lighting mode, where both sides simultaneously display the same signal lighting effect, making 600 Double Sided In Line Canopy Traffic Light suitable for gantry crane cantilever installation. This ensures that operators at various crane angles can clearly see the signals from a distance, effectively resolving the issue of visual blind spots associated with single-sided lighting fixtures.
Remote Central Control Function：
Supports two mainstream control modes: discrete dry contact control and RS485 communication control; can be integrated with high-speed, tunnel, or toll station monitoring host platforms, enabling administrators to remotely switch lane opening/closing states from the monitoring room; Optional status feedback function: the lighting fixture sends its actual illumination signal back to the backend system, allowing the monitoring system to verify whether the device is operating correctly and facilitating fault diagnosis and inspection.
All-weather stable display function：
Equipped with specialized high-brightness LED light sources, 600 Double Sided In Line Canopy Traffic Light ensures long-range visibility under bright daylight, rainy nights, or foggy conditions; its sealed, waterproof, and dustproof design is suitable for outdoor environments or humid, dusty tunnel settings, enabling continuous operation 24/7; the device supports a wide voltage range, ensuring the signal remains stable without flickering or loss of control even under voltage fluctuation conditions.
Addressing core customer pain points
Conventional single-sided lane lights installed on gantry frames create visual blind spots when vehicles approach from various angles; at curves or sharp turns, drivers may fail to see traffic signals from a sufficient distance, increasing the risk of inadvertently entering restricted lanes.
A dual-sided lighting design enables the simultaneous display of the same signal in both directions, covering a wide range of driving angles and eliminating visual blind spots. This ensures that drivers in different lanes or from various driving positions can clearly identify traffic instructions, thereby reducing the risk of misjudgment.
Significant traffic flow fluctuations at highways, tunnels, and toll stations; the need for rapid lane opening/closing during peak hours, accidents, or maintenance operations; low efficiency and high safety risks associated with manual on-site traffic control.
Supports dry contact control; enables one-touch switching between “Red Cross” (stop) and “Green Arrow” (release) modes for remote traffic flow management; eliminates the need for on-site personnel to monitor traffic flow, thereby improving lane management efficiency and ensuring the safety of operational personnel.
Tunnel environments characterized by high humidity and moisture levels; outdoor exposure to intense sunlight and rain; and low-temperature condensation during winter – all of which can cause conventional signal lights to become damaged by water ingress, lead to rapid degradation of LED chips, and result in increased project costs due to frequent replacements.
Fully sealed waterproof and dustproof enclosure (IP55 or higher protection rating), wide operating temperature range (-40°C to +70°C), and transportation-grade, long-life LED light source – designed to withstand harsh operating conditions in tunnels and open-air toll stations throughout all weather conditions, significantly reducing equipment failure rates and replacement frequency, while minimizing subsequent maintenance costs.
When a lane is temporarily closed, drivers may notice this too late; an emergency lane change can easily lead to rear-end or side-impact collisions, thereby increasing road safety risks and the cost of accident response.
High-brightness LED light source provides clear long-distance warning signals, informs drivers in advance of lane opening or closing status, guides vehicles to change lanes smoothly in advance, reduces instances of emergency braking or forced lane changes, lowers the incidence of traffic accidents, and alleviates the workload on traffic management authorities when handling accident incidents.
With integrated, non-disassemblable lighting fixtures, if a single light panel becomes damaged, the entire equipment must be disassembled – a process that involves lengthy and high-risk maintenance operations at elevated heights.
Modular light panel and side-door maintenance structure allow for the individual replacement of faulty components without requiring the entire lamp to be removed, thereby reducing the duration of high-altitude maintenance, minimizing safety risks associated with high-altitude work, and saving maintenance man-hours.
600 Double Sided In Line Canopy Traffic Light Wiring Instructions
AC85-265V (Power Cord)
1.Green line – Front green arrow; AC85-265V live wire
2.Red line – Front red cross; AC85-265V live wire
3.Brown line – Backside red cross; AC85–265 V Live Wire
4.White line – Backside green arrow; AC85-265V live wire
5.Black wire – Neutral wire
6.Yellow ground wire
600 Double Sided In Line Canopy Traffic Light installation instructions
Sunshade Hat Installation
1Align the trapezoidal bracket hole with the holes on both sides of the luminaire.
2.Insert the M4 screw through the trapezoidal bracket.；
3.Finally, simply tighten the screw (as shown in the figure).
4.The installation method for the sunshade panel is the same as that for the trapezoidal bracket.
Lifting bracket installation
1.1.First, use an M16×35 screw to connect the upper bracket to the middle bracket; then secure the assembly with a nut, a spring washer, and a spacer.
2.Then align the screw holes of the lower and middle brackets (according to the required on-site length), insert two M12×80 screws into the respective screw holes, and secure them with M12 nuts; the completed installation is shown in the figure.
3.Install the mounted bracket with the lower end facing downward, aligning it with the screw holes at the top of the luminaire; then secure the bracket using four M12×25 screws along with spring washers and plain washers.
4.Finally, secure the indicator light, which is already mounted on the bracket, to the desired position using screws.
600 Double Sided In Line Canopy Traffic Light Production Details
600 Double Sided In Line Canopy Traffic Light Batch Aging
600 Double Sided In Line Canopy Traffic Light Usage Instructions
The casing of this product is made of sheet metal with an electrostatic coating. Avoid heavy pressure to prevent damage to the casing. 600 Single Side In-line Canopy Light must be powered on under the guidance of a professional, and you cannot disassemble the lamp on your own without permission.
600 Double Sided In Line Canopy Traffic Light After-sales Warranty Terms
• Warranty period: 3 years; the warranty covers only the main unit of the lighting fixture; accessories are not covered; custom-made products are excluded.
• Return method: Customer returns
• Exclusion of Liability: Malfunctions resulting from human-induced damage or natural disasters are not covered under the warranty.
• Logistics Note: The shipping cost for returned items shall be borne by the sender in a one-way manner.
| Product Name Double-Sided Through-Hole Canopy Light | |
| Product Model WDM-CD600-02-RG | |
| Number of LEDs 192 red LEDs × 2, 140 green LEDs × 2 | |
| LED Colors Red/Green | |
| Red Wavelength 620–625 nm | |
| Green Wavelength 500–505 nm | |
| Luminous Flux Red > 5,000 mcd, Green > 6,000 mcd | |
| Operating Voltage AC 220 V ±15%, 50 Hz ±2 Hz | |
| Rated Power ≤ 20 W | |
| Housing Material | Electrostatic spray coating, sheet metal enclosure |
|---|---|
| LED Beam Angle | Horizontal -30°, Vertical -30° |
| Operating Current | ≤250 mA |
| Dimensions | 600 × 600 × 120 mm |
| Operating Temperature | -40°C to +80°C |
| Relative Humidity 10%–95% | |
| Housing Color Black | |
| Visibility Distance ≥300 m | |
| Service Life 100,000 hours | |
| Mounting Method Telescoping mounting bracket; ceiling-mounted; connected to the mounting bracket using a Φ12 mm threaded rod | |
| Applications Toll booths, tunnels, parking lots, etc. | |
| Warranty Period 2 years | |
| Brand Weimei | |
| Accessory | Quantity | Notes |
| lamp | 1 unit | Red/Green dual-color display – meets various warning requirements across different scenarios. |
| sun visor | 1 set | Anti-glare |
| M4*10 screw | 10 pieces | Fixed sunshade |
| Stent | 1 set | Install a fixed light fixture |
| Certificate of Qualification | 1 serving | As a material release certificate |
| Product Manual | 1 serving | Includes product technical specifications, illustrated installation steps, and a safety and maintenance guide |
